In this edition of the Harvest Report we're going to show you the view through the eyes of our robots. You'll be able to see the world like Harvey sees the world, and gain an appreciation for what life is like for a mobile autonomous nursery and greenhouse robot.
Enjoy,
Matt
A Robot's View of the World
The Harvest Automation HV-100 Robots use a variety of sensors to "see" the world and understand their place in it. Accelerometers, gyroscopes and motor encoders each impart some notion of the robot's surroundings, but it's two other sensors - a laser range finder and boundary sensors - that are effectively the robot's eyes, which we rely on for the most important information.
The laser rangefinder is the main vision sensor used by the HV-100 robots. This sensor is used to locate plants that need to be moved and to identify the pattern and location to move a plant into. It's also used to see obstacles in the robot's path, and identify team-mates. The laser rangefinder sees the world as a 2-D plane about 5 inches off the ground. The laser rangefinder is the shiny conical object to the left of the front roller, when looking at the robot from the front.  The rangefinder emits a beam of IR parallel to the ground and sweeps that beam in a circle, while simultaneously looking at reflected signals that bounce off the surroundings. From this information it can construct a 2-D map of it's surroundings.
The boundary sensors are the four orange cups attached to the ends of the tube frame. Boundary sensors are used to locate and follow the yellow retro-reflective boundary tape that users  deploy to mark the edge of the bed. They work by shining IR light onto the tape and looking for the  reflected signal. The robot servos its path on this tape and follows it until it finds a spot to place the plant that it is carrying.
For the Harvest Automation engineering team to get an accurate view of what the robot is seeing, we've constructed a tool that we call Mindprobe which collects all the sensor data, interprets it and displays this in a graphical form as shown below:
The first step in a spacing task is to select and pick a target. In the image below the robot has selected the pot denoted by the green circle with a star.
Once a pot has been picked the HV-100 turns toward the boundary tape. In the image below, the boundary is detected by the two front boundary sensors at the locations marked with bold red 'X's. Paths marked with blue arrows indicate previous circuits that the robot has taken.
After the HV-100 has found the boundary it turns to follow the boundary using the right front and rear boundary sensors (in this example). It then begins searching for placed pots (indicated in the below image by the red circles), and empty pot placement locations (dashed red circles).
Finally the HV-100 chooses a pot placement location, plots a path to that location and deposits the pot that it is carrying.  From there it turns toward the unspaced pots and repeats the entire operation.
Visit our YouTube Channel to view a video download of Mindprobe on a Harvest Automation HV-100 in action.

Harvest HowTo
In this Harvest HowTo section we provide some refresher tips for adjusting your robot's gripper for peak performance.
The gripper is the part of the HV-100 that grabs hold of containers. The gripper is fully adjustable and configurable in both height and diameter and can handle containers from under 1 gallon to 5 gallon. The gripper is available in three types: Type-A for small containers, Type-B for medium to large containers and Type-C for tall containers. Most users will find that the Type-B grippers can handle the widest range of container sizes and are most appropriate for their operation.
For a quick demo of gripper setup click the YouTube video to the left.
A user can position the gripper by highlighting ADJUST GRIPPER from the GRIPPER SETUP screen and pushing the Selector Knob.

When prompted, press the Start Button in either direction to lower the gripper for adjustment. The robot will beep, then extend the manipulator arm and put the gripper in the closed position.
Quick Tip: While in the ADJUST GRIPPER behavior, pressing the Start Button (in either direction) toggles the gripper between OPEN and CLOSED.
Make height adjustments by pulling this knob and sliding the gripper up or down
Diameter adjustments are made by pulling up on these knobs and rotating paddles
Diameter adjustments are completed by removing these knobs and setting the pusher bar position
New Customers
Things are heating up in Texas as we welcome sites from Color Spot nurseries! They specialize in the distribution of high quality bedding plants, vegetables, herbs, shrubs, premium blooming plants, ground cover, ornamentals and more. The Color Spot family is committed to excellence. They pride themselves on the success of their customers and the satisfaction of their ultimate consumers.
Introductory Robot Rental Program
Special Robot Rental Program for New Customers

4 Robots, 3 Months, $15,000. Seeing is Believing! Rent robots today to see all the benefits that mobile autonomous robots can bring to your operation. Click on the button to the right and enter your contact details on our website and one of our representative will be in touch.

  • 4 Robots
  • 3 Months
  • $15,000

For a limited time Harvest Automation is offering low introductory robot rental terms.

 

We're so confident that you'll see the value the HV-100 robots, that if you choose to purchase your robots we'll credit 100% of the rental fee to the price of purchase.

 

Get started today to begin seeing all the benefits:

  • Low cost per plant move
  • 5-15% more plants on a bed
  • Faster crop turnover
  • Less pruning and rework
  • Reduced water usage
  • Reduced fertilizer usage
  • Reduced chemical usage
  • Reduction in Workers Compensation Insurance premiums
  • Improved worker health and safety
  • Lower employee turnover
  • Lower exposure to labor law changes
  • Lower exposure to health care law changes
  • Higher plant quality
  • More predictable production schedules
Upcoming Events
Regional Demo at Poole Brothers Nursery
Join us at Poole Brothers Nursery in Louisiana on December 2nd from 10 AM to Noon. We'll be holding a live demonstration of the HV-100 plant moving robots working in a real nursery setting. Representatives of Harvest Automation will be on hand to answer questions, provide information about the robots and share details of our rental and sales programs.

Poole Brothers Nursery
12781 Highway 165 S
Glenmora, LA 71433

For more information please contact Beth Paul at (978) 528-0378 or bethp@harvestai.com
We look forward to seeing you there! 
MANTS 2015
For those of you who can't make it down to Louisiana, Harvest Automation will have a booth at the MANTS 2015 Trade Show. Come join us at Booth #2973 from January 14th through the 16th at the Baltimore Convention Center. See the HV-100 in action and talk to a representative to find out how you can experience the benefits of robot automation at your operation.
Find Out More

For more information about the robots, our introductory rental program, and financing options, or to schedule an on-site demo contact Harvest Automation at:

(978) 528-4250

 sales@harvestai.com;

 

For more information about Harvest Automation and the HV-100, please visit http://www.harvestai.com.

Copyright � 2014. All Rights Reserved.